H&R Foot Notes

Foot Note :3

All DR-Systems require longer wheel bolts. These must be ordered separately. When ordering wheel bolts, please follow these guidelines:

a) If possible, name the brand of wheel.

b) New bolts must be longer than the original bolts by the width of the wheel spacer used.

c) The bolt head must be identical to the existing bolt:
Taper 60° End digit 01
Round head for M12/d24 mm, for M14/d28 mm End digit 02
Round head for M12/d26 mm (e.g. OE VAG-wheels) End digit 03
Flat head for Porsche original wheels M14 x 1.5 End digit 06

d) Safety guidelines
(Minimum number of turns for wheel bolts / nuts):
M12 x 1.25 = 8.0 turns = approx. 10 mm of load bearing shaft length
M12 x 1.50 = 6.5 turns = approx. 10 mm of load bearing shaft length
M12 x 1.75 = 6.5 turns = approx. 12 mm of load bearing shaft length
M14 x 1.25 = 9.0 turns = approx. 12mm of load bearing shaft length
M14 x 1.50 = 7.5 turns = approx. 12 mm of load bearing shaft length
1/2" UNF = 8.0 turns = approx. 11 mm of load bearing shaft length

e) Please ensure that the wheel bolts do not damage any part of the brake system (ABS sensors, etc.). Turn the wheel by hand and check clearance on the inside of the hub. The wheel should rotate freely. (Maximum tolerance for some vehicles is only 2mm -- i.e. Rear Axle Mercedes).

Foot Note:7

Foot Note: 8

If the depth of the wheel spacer is smaller than the length of the standard studs, the wheels used must allow for small cavities in the mounting pad of the wheel. If using wheels without cavities, the standard studs should be shortened so that they do not extend beyond the height of the spacer.

Foot Note: 12

These vehicles have different shoulder diameters in the studs depending on model and axle. The DRS installation information must be carefully followed. If exchange of the studs is required, please call us at 1-888-827-8881.

Foot Note: 17

Depending on model, axle and year, Mazda vehicles have different diameters in the shoulder of the studs. Please see the following list for the measurements of the studs required for installation. The wheel spacers shown in the catalog will be supplied with shoulder bolts d=13.00. If you need d=14.85, please add a "1" at the end of the part number.

Vehicle	Model	Shoulder Front Axle	Shoulder Rear Axle
DRS Wheel Spacers - Mazda DRS wheel spacers / required DRS shoulder
323	BG	small 3.00 mm	small 13.00 mm
		up to chas. no. 753743	up to chas. no. 773461
323	BG	large 14.85 mm	large 14.85 mm
		from chas. no. 753744	from chas. no. 773462
323	GT/GTR	small 13.00 mm	large 14.85 mm
323	BA/BJ	large 14.85 mm	small 13.00 mm
626	GE/GEA	small 14.85 mm	small 13.00 mm
626	GF/GV/GW	small 14.85 mm	large 13.00 mm
MX 3	EC	large 14.25 mm	small 13.00 mm
MX 5	NA	small 13.00 mm	small 13.00 mm
			up to chas. no. 133232
			large 14.85 mm
MX 5	NB	small 13.00 mm	large 14.85 mm
MX 6	GE6	small 13.00 mm	small 13.00 mm
		up to chas. no. 101861	up to chas. no. 101861
		large 14.85 mm	small 14.85 mm
		from chas. no. 101862	from chas. no. 101862
XEDOS	6/9 CA/TA	small 13.00 mm	small 13.00 mm

*Information is subject to change without prior notice.

Foot Note: 14

When using 50 mm wheel spacers in conjunction with standard wheels, the standard bolts will be too long. They must be shortened by 5 mm or replaced with a new bolt, part number 1452802. In this instance, a 17 mm lug wrench must be added to your vehicle toolbox.

Foot Note: 18

The 16 mm wheel spacers are offered for vehicles on which the centering hub is long enough to center the wheel after installation. Alternatively, we offer wheel spacers in 16 mm, 20 mm and 24 mm-with a centering hub. Please see the following list to find the part number for ordering.

Vehicle	System Widening Per Side	Technical Requirements Maximum Height of Centering Hub	Order No.
TOYOTA 5-hole, MZ 54.1	DR / 10	Factory hub height up to 10.0 mm	2025541
VOLVO	DR / 10	Factory hub height up to 11.0 mm	2035650
AUDI/SEAT/SKODA/VW 5-hole	DR / 10	Factory hub height up to 10.5 mm Inside wheel bevel = 7.0 x 45 degrees	2055571
AUDI/SEAT/SKODA/VW 5-hole	DR / 10	Factory hub height up to 12mm Inside wheel bevel = 4.0 x 45 degrees	2055571B

MERCEDES	DR / 10	Factory hub height up to 9.0 mm	2055665
HONDA 4-hole, MZ 64.0	DR / 10	Factory hub height up to 10.0 mm	2064640
HONDA 5-hole, MZ 64.0	DR / 10	Factory hub height up to 10.0 mm	2065640
NISSAN 5-hole, MZ 66.2	DR / 10	Factory hub height up to 9.5 mm	2065662
HONDA 5-hole, MZ 70.0	DR / 10	Factory hub height up to 10.0 mm	2065700
BMW	DR / 10	Factory hub height up to 11.5 mm	2075725
BMW E39	DR / 10	Factory hub height up to 11.5 mm	2075740
VOLVO	DR / 12	Factory hub height up to 11.0 mm	2435650
AUDI/SEAT/SKODA/VW 5-hole	DR / 12	Factory hub height up to to 18.0 mm Inside wheel bevel = 7.0 x 45 degrees	2455571

MERCEDES	DR / 12	Factory hub height up to 10.0 mm	2455665
BMW	DR / 12	Factory hub height up to 12.5 mm	2475725
BMW E39	DR / 12	Factory hub height up to 12.5 mm	2475740
ALFA ROMEO	DR / 10	Factory hub height up to 10.5 mm	20135580
MAZDA 4-hole, MZ 54.1	DR / 10	Factory hub height up to 11.5 mm	20245410
TOYOTA 4-hole, MZ 54.1	DR / 10	Factory hub height up to 11.5 mm	20245414
HONDA 4-hole, MZ 56.1	DR / 10	Factory hub height up to 10.0 mm	20245616
AUDI/SEAT/SKODA/VW 5-hole	DR / 10	Inside wheel bevel = 7.0 x 45 degrees	20255571
SUZUKI	DR / 10	Factory hub height up to 11.0 mm	20365601
TOYOTA 5-hole, MZ 60.1	DR / 10	Factory hub height up to 11.5 mm	20656014
AUDI/SEAT/SKODA/VW 5-hole	DR / 12	Factory hub height up to 15.0 mm Inside wheel bevel = 7.0 x 45 degrees	24255571

AUDI/SEAT/SKODA/VW 4-hole	DR / 8	Factory hub height up to 14.0 mm Inside wheel bevel = 7.0 x 45 degrees	162345712

AUDI/SEAT/SKODA/VW 5-hole	DR / 8	Factory hub height up to 14.0 mm Inside wheel bevel = 7.0 x 45 degrees	162555716

AUDI/SEAT/SKODA/VW 4-hole	DR / 10	Factory hub height up to 16.0 mm Inside wheel bevel = 7.0 x 45 degrees	202345714

AUDI/SEAT/SKODA/VW 5-hole	DR / 10	Factory hub height up to 15.5 mm Inside wheel bevel = 7.0 x 45 degrees	202555712

AUDI/SEAT/SKODA/VW 5-hole	DR / 10	Factory hub height up to 16 mm Inside wheel bevel = 7.0 x 45 degrees	202555712A

Foot Note: 21

When using our 50 mm and 60 mm wheel spacers for vehicles with sliding doors, be sure to check the clearance of the fitting.

Foot Note: 24

If the hub face of your vehicle is 150mm (most vehicles have 135mm hub face), alternative spacers are available. Please see list below.

DR = 8mm 162555719
DR = 10mm 202555713
DR = 12mm 242555713
DR = 15mm 302555716
DR = 20mm 402555716
DRA = 20mm 4025572
DRA = 25mm 50255712
DRA = 30mm 60255712